Comments for Faux Masters Studio Blog

Comment on Single Glaze Over Kitchen Cabinets – Article 1 by Single Glaze Over Kitchen Cabinets – Article 4 « Faux Masters Studio Blog

Single Glaze Over Kitchen Cabinets – Article 4 « Faux Masters Studio Blog — Tue, 29 Jun 2010 00:29:49 +0000

[...] Fourth in a series of articles called “How To Weeklies” that address jobsite issues. This week’s article addresses problem-solving techniques when the job presents unanticipated issues. (Click here to visit article 1) [...]

Comment on Single Glaze Over Kitchen Cabinets – Article 1 by Single Glaze Over Kitchen Cabinets – Article 3 « Faux Masters Studio Blog

Single Glaze Over Kitchen Cabinets – Article 3 « Faux Masters Studio Blog — Mon, 28 Jun 2010 23:24:08 +0000

[...] Third in a series of articles called “How To Weeklies” that address jobsite issues. Now that the job is in progress, how do I successfully bring this project to completion? This week’s article will discuss tips to applying a glaze, issues that may come up and the importance of topcoating. (Click here to visit article 1) [...]

Comment on Single Glaze Over Kitchen Cabinets – Article 1 by Single Glaze Over Kitchen Cabinets – Article 2 « Faux Masters Studio Blog

Wed, 16 Jun 2010 23:03:13 +0000

[...] Second in a series of articles called “How To Weeklies” that address jobsite issues. This week’s article discusses the first day on the job, what to do, how to do it and all the other small things in-between. Follow along with me to discover real time, valuable information regarding cabinetry finishing. (Click here to visit article 1) [...]

Comment on Faux Masters Giveaway by Stephanie

Stephanie — Mon, 01 Feb 2010 22:30:42 +0000

RsCrete, like most Faux Effects products, are basically “paint systems.” These products don’t catalyze like concrete or casting (hot) plasters. RsCrete is extremely durable and cures very hard with a tight structure.
The proper technique for applying RsCrete over concrete is:
1. Do a moisture test to make sure your concrete doesn’t draw up moisture from underneath somewhere.
(This website has an article to look at regarding how to do this –
http://www.concreteconstruction.net/industry-news.asp?sectionID=715&articleID=259135&artnum=1)
2. You may need to acid etch (read manufacturers label well!) the concrete surface to open up the pours, depending on your type of concrete. Neutralize the acid and rinse WELL. Let dry a few days.
3. Apply a high quality water-based primer to dive deep down into the pourous surface to create a good physical bond. You can use AquaBond (SetCoat), 2 coats.
4. Apply RsCrete with method of choice. If you are going to make grout areas, skim RsCrete first, let dry, then tape your grout areas and skim again. You could tint the product to colorize your grout as well.
5. Topcoat for extra durability and to fill in the crevices in the product so dirt and grime don’t build up.
If you apply 1-2 tight skims of the RsCrete Super Fine as your final layer, you may not need to apply a topcoat over low traffic areas.
I should also note: All Crete products need to be fully mixed up before application. Some separation is natural.

Comment on Faux Masters Giveaway by Phil

Phil — Fri, 22 Jan 2010 03:02:03 +0000

Have a question about RScrete. I currently work for someone who uses elite crete systems. To prepare smooth poured surfaces( like basements and other interior floors) we need to grind down to the aggregate to get a good bond. I was wondering what you need to do for the same surface for RScrete. And for grouting patterns, is the aquabond priming coat the grout layer, or do you put a first coat of crete after the aquabond as the grout layer. If anyone can answer or help, much appreciated!

Comment on Holiday Play by endacrowe

endacrowe — Tue, 12 Jan 2010 01:19:32 +0000

i could not agree more ; trying to come up with a finish really requires that you have to do a clean sweep ; the less clutter and mess the easier it will be to get the juices flowing and will make life a lot easier ; you have to start with a blank canvas; i could not tell you the amount of times i have walked into my studio/workshop and just had to say ‘ o no ‘ let me out of here . bottom line ; for me it really is worth the time spending time getting every thing sorted out before getting into another project

Comment on It’s Raining It’s Pouring by Melissa

Melissa — Wed, 30 Dec 2009 18:35:03 +0000

Was it a waterbase primer?
This is common when applying a waterbase primer over older ash and oak cabinets. When you sand it releases tanic acid that reads through the finish with a rust/nicotine color. We would recommend that you prime with Kilz oil-base Original, do not get the waterbase primer even if it says stain resistant.
Once you prime with the oil-based kilz you can proceed with your technique.
Good luck.

Comment on It’s Raining It’s Pouring by Phil

Phil — Wed, 30 Dec 2009 03:55:05 +0000

I have problem> I am doing a white finish over pre existing stained and lacqured cabinets. I am gettint rust or yellow colored spots in some areas. My process was to sand down the surface, 2 coats of promer, a coat of acrylic basecoat, distress, a coat of setcoat clear, glaze, and seal with varnish plus. The spots seemed to appear after I applied the setcoat clear. Please help!

Comment on It’s Raining It’s Pouring by hominidme

hominidme — Mon, 28 Dec 2009 21:02:39 +0000

I don’t always have time to stir up my pigments, but I have this really cool mixing tool called the drill! Okay, not funny.
No really, I attach on of those egg beaters to my drill and insert into (larger) containers (although I think the art stores have smaller bits for stirring textured art materials), or I use a drill bit called a spade for smaller containers. You know, you could attached just about anything that would fit into your drill head – use only at low speeds!! Just thought I’d share.

Comment on Holiday Play by hominidme

hominidme — Mon, 28 Dec 2009 20:45:46 +0000

I find that before the creative juices can flow I need to clean up my studio. Even then it takes some “sponging up” I call it to get a direction to go in. After reading the forecast and design pages, it seams like an ecclectic mix for the future.
In this unsure market I guess its “tread lightly.”